Opened 10 years ago

Last modified 5 years ago

#515 new flight processing

GB14/00, flight day 078/2014, Little Riss

Reported by: knpa Owned by: stgo
Priority: immediate Milestone: 2014 data processing completion
Component: Processing: general Keywords:
Cc: Other processors:

Description

Data location: /users/rsg/arsf/arsf_data/2014/flight_data/arsf_internal/GB14_00-2014_078_Little_Riss/

Data arrived from ARSF via network transfer on 19/03/2014

GB14/00 Scientific objective: Boresight

GB14/00 Priority: urgent

PI: ARSF

Notes: FENIX 25 lines

Sensors:

LiDAR (Requested)
FENIX (Requested?)

Change History (15)

comment:1 Changed 10 years ago by stgo

Nav data processed, good solution achieved

comment:2 Changed 10 years ago by stgo

Beginning lidar calibration, Range cal results:
Range Offset A1: 0
Range Offset A2: 0.006
Range Offset A3: 0.040
Range Offset A4: -0.011

Range Offset B1: 0.000
Range Offset B2: 0.002
Range Offset B3: -0.002
Range Offset B4: 0.020

comment:3 Changed 10 years ago by stgo

Have computed scanner offsets and most (all) flightlines are way off the scan correct value given by leica (-10340) averaging them all has resulted in 16640 as a potential value.

There is however one flightline that carries a value of -172016 which is considerably above the other values given, removing this from the averaging results in a value of 10310. I will try to run the calibration using both values to see differences.

comment:4 Changed 10 years ago by stgo

Pitch roll and heading values found as:

roll-0.003918414
pitch0.00113716
heading0.00056484

The roll error is an average of the best values for high and low alt lines being:

high−0.003991482
low −0.003845345
Last edited 10 years ago by stgo (previous) (diff)

comment:5 Changed 10 years ago by stgo

Range calibration completed using averaged roll error.

Lascontrol gave a result of -1.58854 which was used with RangeCardCal to get the following values:

A1-1.58854B1-1.589
A2-1.582B2-1.587
A3-1.548B3-1.591
A4-1.599B4-1.569

Lascontrol gave an average dz of 0.0164776 with std dev of 0.0206099 on low altitude
0.0683441 with std dev of 0.0197977 on mid altitude and
0.0525533 with std dev of 0.0377199 on high altitude.

Last edited 10 years ago by stgo (previous) (diff)

comment:6 Changed 10 years ago by stgo

The full wave form files were not present so this has not been calibrated.

comment:7 Changed 10 years ago by stgo

Beginning hyperspectral boresight.

comment:8 Changed 10 years ago by stgo

Fenix lines 1 and 2 are errored lines with less than a second of data. Will not be used from here on. SCT values are:

Flightline Fenix
1 0.00
2 0.00
3 0.91
4 0.96
5 0.91
6 0.90
7 -0.06
8 0.96
9 0.95
10 0.96
11 0.92
12 0.90
13 0.95
14 0.90
15 0.96
16 0.93
17 0.96
18 0.96
19 0.96
20 0.96
21 0.96
22 -0.04
23 0.95
24 0.95
25 0.94
26 0.91
27 0.95
Last edited 10 years ago by stgo (previous) (diff)

comment:9 Changed 10 years ago by stgo

Boresight values are:

pitch0.296
roll0.112
heading0.20
Version 0, edited 10 years ago by stgo (next)

comment:10 Changed 10 years ago by mark1

Second attempt at LiDAR calibration, based on the results of the first one but trying to convert to using torsion and pitch error slope (pes) rather than forward laser angle (FLA). Fiddled with boresight parameters and range correction after changing over to torsion and pes.

comment:11 Changed 10 years ago by stgo

I've moved the original processing for the hyperspectral boresight to processing/original_hyperspectral, will move back when dap is finished learning some hyperspectral processing.

comment:12 Changed 9 years ago by stgo

Fenix

This flight did not have dark frames

comment:13 Changed 8 years ago by stgo

Last edited 8 years ago by stgo (previous) (diff)

comment:14 Changed 8 years ago by stgo

Test2

comment:15 Changed 5 years ago by dac

Moved hyperspectral processing back.

Note: See TracTickets for help on using tickets.