Version 12 (modified by stgo, 10 years ago) (diff)



This guide describes how to process LiDAR data using alsproc and the ALS Post Processor

Alsproc can either be run locally using (linked as just alsproc) or on the grid using Note that presently it will only run correctly on fedora 19 machines and as such you must submit to the development grid. Check with someone on how to do this, you'll need to update SGE_CELL.


The configuration file is made with the program. It will examine your current working directory and derive a project directory, from which it will determine the best available calibration to base your configuration file on, and populate it with information derived from your flightlines. This can take a while, as it needs to perform a cursory check on all of the raw data.

This presently only works on fedora 19 machines.



airborne@pmpc1322:/users/rsg/arsf/arsf_data/2013/flight_data/uk/RG12_09-2013_121_Wessex# generate_alsproc_config
Gathering details about project...
Using calibration file (/users/rsg/arsf/calibration/lidar/20130219/als50.cfg)...
Collating details for .cfg file...
Writing .cfg file
Scanning flightline 130501_093511... ok
Scanning flightline 130501_094820... ok
Scanning flightline 130501_100234... ok
Scanning flightline 130501_101637... ok
Scanning flightline 130501_102953... ok
Scanning flightline 130501_104304... ok
Scanning flightline 130501_105631... ok
Scanning flightline 130501_113351... ok
Scanning flightline 130501_114825... ok
Scanning flightline 130501_120434... ok
Scanning flightline 130501_121952... ok
Scanning flightline 130501_123433... ok
Scanning flightline 130501_125655... not ok, check failed on duration
all done

Flightlines which alsproc thinks it might not be able to process based on this check will be flagged here, as in the case of the last flightline, and not be marked to be processed.

Next, edit the .cfg file created. If you did not specify, it will be under processing/als50/*.cfg.

Fields of particular interest to you as a data processor are:

  • output-format - can normally be left as the default
  • output-projection - will need to be set per-flight depending on where the flight is based, consult the projections table below
  • output_dir - default is probably fine, but it can be useful to change, especially when working on the pitch and roll values later
  • sol-file - change this to the location of the sol file created during navigation processing, it may already be filled in for you
  • sup-file - as with the sol file
Projection Use-Case output-projection
British National Grid all British flights ukbng
UTM everywhere else utm zone=<zone number> hemisphere=<n/s> hrz_datum=wgs84 vrt_datum=wgs84

You may also change the output formatter from the standard LiDAR formatter. The following table lists the options and values you should enter in each field.

Format Use-Case output-format output-file-ext (recommended)
las (default) normal processing las12_las .las
ascii experimental/analytical reasons txt .txt

It is likely that there will be a pitch/roll offset as described below. Correcting this works in a similar manner to hyperspectral SCT correction. You will need to add the following fields to the cfg file to iterate over a range of pitch/roll/heading corrections:

#roll-correct = -0.0035000
roll-start = -0.0030000
roll-end = -0.0040000
roll-inc = -0.0001

This would result in 11 las files being created, each at a 0.0001 increment. Switch out roll for pitch or heading if you need to process those. You need to comment out or remove the -correct value or alsproc will not run.

Note that you can only run one of pitch/roll/heading as incrementing at present, this is to stop confusing files but could be added in if it is felt it is needed.

Be certain about your -inc value as this can result in very large numbers of files being produced.

You will then see a section for each flightline. process_line should be set to true for each flightline unless there was some problem, in which case the maintainer for alsproc should be contacted.

output-file = %(output_dir)s/ldr110618_090736%(output-file-ext)s
process_line = true
line_number = 1

# GMT 09:07:52 to 09:08:39, 47.3 seconds
start-time = 1640,551272.000006
end-time = 1640,551319.282274
delta-avg-diff = 0.000006667852
scanner-fov = 18.932618
scan-rate = 58.214212
multi-pulse = false


Alsproc is fed its arguments with the wrapper script, which also handles certain LiDAR preformatting if using las12_las.

alsproc processing/als50/2013121.cfg

To specify which flightline:

alsproc -f 140306_130407 2013144.cfg

or to run on-grid: 2014238.cfg

Log files will be kept for each flightline in the directory specified by log_dir in the configuration file, for your use if alsproc should suffer from some processing error. If you are running on the grid separate log files directly from the gridnodes will be outputted as well, these can be of use when checking pre-processing errors.

Pitch and Roll Errors

Follow the instructions above using the roll/pitch/heading correct values as these will be from the boresight for the current time period. Once you have set off generation wait for the files to create. This can take a while; 20 minutes to 20 hours depending on the size of the dataset and load on the network, it will be noticeably faster on the grid.

After creation is complete inspect the initial files to check for pitch (along track shifts) and roll (across track shifts) errors, it is unlikely that the boresight parameters will get you a perfect solution first time. Once you have an idea of the error you are looking at start using start/end/inc values to correct.

On early iterations, you may identify just a few flightlines and focus your efforts on those, but you must check flightlines from across the entire dataset, as pitch and roll has been known to change over the course of a flight in the most unfortunate cases.

The best method is to search for rooftops or other recognisable features both along and across areas of overlap using lag. It should look like this:

pitch error shown

Using the ruler tool come up with the best possible approximate for lateral displacement both along and across the overlap. Normally this will be in the region of 50cm to 10cm. If the displacement is less than 5cm or 10cm in both directions then the files you have should be ok to use and you can use the pitch and roll errors you used for this attempt in your final solution. If not, you will need to estimate some new pitch and roll errors and try again. An example of acceptable pitch and roll errors is given below.

pitch error corrected

Determine the direction of your error. You need to decide whether to add or subtract from each of the pitch and roll error in the fields pitch-correct and roll-correct respectively. Look at the times of a few points in each flightline to determine each of their directions, and then decide whether you want to roll the angle of the laser clockwise or anticlockwise around the direction of travel of the plane to move the data left or right respectively; and whether you want to pitch up or down to move the data forwards or backwards respectively.

The table below indicates the effects of addition of subtraction on each axis.

Operation Pitch Roll
addition backwards left
subtraction forwards right

You may estimate the magnitude of your adjustment yourself based on your own intuition or previous observations if you wish. Using an equation can help you zero in on the correct solution more quickly, especially in your first two or so observations.

e = arctan( d / (h1 + h2) )

Where: e will be your error to add to or subtract from the value used to compute this dataset, d is the difference you measured in lag, h1 and h2 are the heights of the plane in each flightline above the terrain at the time of the observation. (Make sure you convert everything to the same units of measurement, such as metres.)

Now return to processing the dataset, you can inspect the data and pass it off, or you can perform another iteration to get the match even closer. The number of iterations you will need to do can vary, but often depends on the quality of the navigation data.

Attachments (3)

Download all attachments as: .zip